Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
G
Rockbag Fingerboard Saver 1 narrow
Rockbag Fingerboard Saver 1 narrow
Previously I have used the Göldo WS045 Fretboard Guard which measures approximately 80mm x 22mm with a slot that measures approximately 3 mm x 69 mm.
I found the Göldo slot to be too large and so I thought I would try the Rockbag version.
To start with the Rockbag actually contains two guards along with a couple of elastic bands to hold them in place.
The Rockbag fingerboard savers are available in three sizes, this is the narrow version.
The guard measure approximately 80mm x 60mm with a slot that measures approximately 70mm x 1.8mm
The guards are very neatly cut out from 0.2mm thick stainless steel with no obvious rough edges to worry about.
The slot is very narrow and I found it was too narrow for most of my guitars, certainly too narrow for any of my Gibson and most of my Fenders.
It only fitted two Japanese fenders, (a FSR competition stripe mustang and a '62 custom telecaster) both with really narrow vintage style frets.
The guards work well, much better than the Göldo guard and I will be ordering the two other sizes as soon as possible as they are very useful.
Previously I have used the Göldo WS045 Fretboard Guard which measures approximately 80mm x 22mm with a slot that measures approximately 3 mm x 69 mm.
I found the Göldo slot to be too large and so I thought I would try the Rockbag version.
To start with the Rockbag actually contains two guards along with a couple of elastic bands to hold them in place.
The Rockbag fingerboard savers are available in three sizes, this is the narrow version.
The guard measure approximately 80mm x 60mm with a slot that measures approximately 70mm x 1.8mm
The guards are very neatly cut out from 0.2mm thick stainless steel with no obvious rough edges to worry about.
The slot is very narrow and I found it was too narrow for most of my guitars, certainly too narrow for any of my Gibson and most of my Fenders.
It only fitted two Japanese fenders, (a FSR competition stripe mustang and a '62 custom telecaster) both with really narrow vintage style frets.
The guards work well, much better than the Göldo guard and I will be ordering the two other sizes as soon as possible as they are very useful.
0
0
Ohlásit hodnocení
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
J
Good enough. What can you say and what would you say
Its made for a purpose and does it well.
There is not much more to add.
Handy discovery if you had never heard of it. And they last....I use them quite a lot.
There is not much more to add.
Handy discovery if you had never heard of it. And they last....I use them quite a lot.
0
0
Ohlásit hodnocení
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
AK
?Simple thing, tricky to ues
This does the thing it should do; protects your fingerboard when filing or polishing your frets.
The hard part is use rubber bands to hold it on its place. I usually end up holding it by hand instead of using rubber bands. Holding this is easier if you add some duct tape to sides to make it a bit bigger and easier to hold.
The hard part is use rubber bands to hold it on its place. I usually end up holding it by hand instead of using rubber bands. Holding this is easier if you add some duct tape to sides to make it a bit bigger and easier to hold.
0
0
Ohlásit hodnocení
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
R
Quality All Around
Ordered the full set but 1 was missing due to a whole in the box when received. Quick e-mail to the service department and the one missing was on the way. Great products and support. What more can you ask for.
0
0
Ohlásit hodnocení
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
so
Great
Good for protecting the fingerboard, although maybe it should be more sturdy than it is. It does what it has to do. Good!
0
0
Ohlásit hodnocení