K obsahu stránky

Pop Filter with 3D Arm

  • Exclusive Thomann Edition
  • Lightweight and space-saving
  • Perfect for travelling
  • Multiple ball joints for flexible adjustment
  • Solid clamp with wide clamping range from 15 to 35 mm
  • High-quality pop filter with double-covered nylon and large screen diameter of 15.7 cm
  • The 360° rotation possibilities of the three joints offer the option to mount the pop filter in any position
  • Arm length: 62.5 cm
  • Weight: 377 g
  • K dostání od Únor 2022
  • Číslo produktu 520616
  • Prodejní jednotka 1 ks
  • Component type Popkiller
385 Kč
Všechny ceny vč. DPH
Na skladě
1

128 Hodnocení zákazníků

4.7 / 5

Zpracování

86 Recenze

JB
Jakub B 04.09.2025
Trochu masivnější, ale je super. Samotný pop filter bez stojanu je s mikrofonním závitem, takže ho připevníte třeba na velký stojan na mikrofon, pokud potřebujete. A stojan k pop filtru jde zas využit i na jiné věci, třeba na mikrofony. Super věc za super cenu, která má více využití.
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení

O
Milé překvapení
Omnion 12.03.2025
Tento pop filtr byl pro mě velmi milé překvapení, je velmi variabilní, díky kvalitně provedeným kloubům drží výborně v jakékoli pozici.
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
B
Unbelievably useful. Amazing.
Birdiesven 06.03.2022
This thing is simply fantastic. Not only is it a pop screen (obviously), you can unscrew the pop filter head and fit anything else to it that will take a standard microphone screw adapter (ie. 5/8" Male / 3/8" Female). This means that it can be used as an adjustable mic stand by fitting a mic clip to it or anything else you can think of that uses the same connector. Then there's the fact that it's modular – each individual arm linkage is removable meaning that if the whole thing is too long, just remove one or two of the linkages. Too short? Buy two and add more linkages to one of them. The possibilities are endless and I think the manufacturer is seriously underselling the usability of this item. I'd give it six stars across the board if I could. Highly recommended.
Zpracování
12
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
S
Finally, a pop shield that stays where you put it.
Stevetf 25.05.2023
I was tired of drooping pop shields. Where most pop shields use a flexible goose neck, this one has a linkage system with multiple ball joints that can be individually locked. This novel design of pop shield is not only inexpensive, but IT WORKS! The Gravity MA 3D A POP 1 is easy to position, and stays in position.

Although it is made mostly of plastic, so long as it is treated with a reasonable amount of care, it looks like it should give long and trouble-free service. (I'll update this review if that proves to be not the case).

The ball joints don't need to be very tight - just nip them up enough to hold their position and the pop shield will stay exactly where you put it. (over-tightening could be a point of failure, but there is absolutely no need to over-tighten).

The shield itself comprises two layers of thin fabric with a gap between the layers, which is noticeably more effective than single layer designs.

The thing that surprises me most about the Gravity MA 3D A POP 1 is that it isn't the number #1 best selling pop-shield. If you're looking for a pop shield that is easy to position and stays where you position it - this is the one! Currently priced at under £14 GBP it is among the cheapest pop shields, and is one of the best at any price.
Zpracování
2
0
Ohlásit hodnocení

Ohlásit hodnocení